P0108 and P0113 after ramair upgrade

Vee · May 4, 2015

charlie farley said:
P0108 is intake manifold pressure and p0113 is intake temp check the plugs that you have disconnected when you fitted the ram air, also the start relay behind left side panel the manual will tell you which is which you can swap the fan one with the starter one to see if that is a faulty relay. I have an 08 classic so you may need to refer to the roadster manual for exact location.

Last evening I swapped relay, but no luck.
Here is the video.
Triumph Rocket 3 startup problem:

CanberraR3 · May 4, 2015

I wish I could help but I'm no good on electrical stuff.
I did notice 2 things in your video. The second time you pressed the starter the headlights seems to be flickering. This didn't happen the other times. Not sure what that means but it is odd that it only did it that one time.
Also, your auxiliary lights were on. Have you tried to start with lights on low beam and the aux lights turned off. Surely that's too much load for the system.

1098cracy · May 4, 2015

I don't think you should hold the clutch lever in all the time, the ecu control needs to see it being switched which is what happens when u pull it in.
It sounds like you have a big short on the ignition side. Unplug the lights etc to eliminate that side of the system.

Vee · May 4, 2015

1098cracy said:
I don't think you should hold the clutch lever in all the time, the ecu control needs to see it being switched which is what happens when u pull it in.
It sounds like you have a big short on the ignition side. Unplug the lights etc to eliminate that side of the system.

Okay, I'll try starting it today with all lights unplugged by taking out fuse.

1olbull · May 4, 2015

I had a very similar issue to this last week before the trip to RAA.
I had a nearly new battery in the bike.
Out of desperation I went and bought another new battery, installed it and everything's working fine so far. I would suggest you put a new battery in your bike and then go from there.

Vee · May 4, 2015

1olbull said:
I had a very similar issue to this last week before the trip to RAA.
I had a nearly new battery in the bike.
Out of desperation I went and bought another new battery, installed it and everything's working fine so far. I would suggest you put a new battery in your bike and then go from there.

Any suggestions for battery. Please.

Triple Trouble · May 4, 2015

Vee said:
Okay, I'll try starting it today with all lights unplugged by taking out fuse.

The bike will not start with the headlight fuse removed.

1olbull · May 4, 2015

Vee said:
Any suggestions for battery. Please.

The battery that failed me was purchased on the Internet. The name escapes me right now, but it was bright yellow in color. It was the first and last battery I shall buy online.
I like the interstate batteries, but
because the time was short for leaving to Arkansas, I picked up a battery at Baxter Auto Parts. So far it seems to be doing the job just fine.

CanberraR3 · May 4, 2015

Just go with the OEM Yuasa.

Vee · May 5, 2015

CanberraR3 said:
Just go with the OEM Yuasa.

Cool. Thanks.

P0108 and P0113 after ramair upgrade

Vee

.020 Over

CanberraR3

Living Legend

1098cracy

.060 Over

Vee

.020 Over

1olbull

Riding Motor Since 1950

Vee

.020 Over

Triple Trouble

The Duk of death

1olbull

Riding Motor Since 1950

CanberraR3

Living Legend

Vee

.020 Over

Similar threads

P0108 and P0113 after ramair upgrade

.020 Over

Living Legend

.060 Over

.020 Over

Riding Motor Since 1950

.020 Over

The Duk of death

Riding Motor Since 1950

Living Legend

.020 Over

Similar threads

Privacy & Transparency

Privacy & Transparency