Bazdog
.020 Over
Anyone know where to source clear indicators for a R3 standard?
Clear Indicators
- Thread starter Bazdog
- Start date
Nussekudden
.020 Over
I make them from expoxi and then coat with PMMA.
I sell them for EUR 19 /pcs incl. freight to where ever.
Send me a mail to plastman@telia.com and I make you a set!
I sell them for EUR 19 /pcs incl. freight to where ever.
Send me a mail to plastman@telia.com and I make you a set!
xhdskip
Living Legend
Thats some fine lookin work there Nusse.
Any more examples of what you have done or could do?
How about a clear Rocket tail light lens?
Now don't run out and make one just cause I asked about it,
but if you've already done it and have pictures,
I'd sure like to see it.
Again, Good work and nicely done.
Any more examples of what you have done or could do?
How about a clear Rocket tail light lens?
Now don't run out and make one just cause I asked about it,
but if you've already done it and have pictures,
I'd sure like to see it.
Again, Good work and nicely done.
Nussekudden
.020 Over
Thanks!
I just crashed my bike, so I have plans to make quit a lot of parts during the winter. Only got a carbon fiber fork sheild ready so far.
This week I will do some trials with red lences for those who like to use them as position lights. Hopefully I will get time as well to try to make a smoke lence that don't steal too much light.
Within a month or two I will also have a flat lence ready.
A clear tail light is no problem to make. It would take some 70 - 80 EUR worth on silikon to make the mould, and then some EUR 20 for the material to cast it. The only problem is that the tail light is so thick, that you might be able to see a grey/yellowish tone in the glas. Can't say for sure untill one is made.
I just crashed my bike, so I have plans to make quit a lot of parts during the winter. Only got a carbon fiber fork sheild ready so far.
This week I will do some trials with red lences for those who like to use them as position lights. Hopefully I will get time as well to try to make a smoke lence that don't steal too much light.
Within a month or two I will also have a flat lence ready.
A clear tail light is no problem to make. It would take some 70 - 80 EUR worth on silikon to make the mould, and then some EUR 20 for the material to cast it. The only problem is that the tail light is so thick, that you might be able to see a grey/yellowish tone in the glas. Can't say for sure untill one is made.
Nussekudden
.020 Over
Close up of a set
Mike Sands
Supercharged
These look really nice. Do you have a waiting list now ? Presumably you have to replace the bulb with an orange one?
Mike
Mike
Nussekudden
.020 Over
Mike5100:
It takes 48h to make one, so I'm not very fast. At the moment I could send a set of 4 within about 2 weeks, if I don't have to scrap to many.
Orange bulbs are not too hard to get hold of and I also heard that you could just paint the bulb orange.
I can give you a few links to where to buy them. I recomend that you get the ones with a silver top for maximum stealth.
It takes 48h to make one, so I'm not very fast. At the moment I could send a set of 4 within about 2 weeks, if I don't have to scrap to many.
Orange bulbs are not too hard to get hold of and I also heard that you could just paint the bulb orange.
I can give you a few links to where to buy them. I recomend that you get the ones with a silver top for maximum stealth.
naturaloak
.020 Over
- Joined
- Mar 10, 2008
- Messages
- 31
Look great...been looking for these for a while! email sent. 8)
