Recent content by BDClone

  1. BDClone

    **SOLD** Turn Signal lens R3R

    I would like them if you havent sold them... sending msg
  2. BDClone

    Idle is over 2700 rpm Help

    Hey guys been busy with family and honey do's so haven't had time to finish sorting out my issues. I did get it to idle normally but when when I took up the road and back it kept wanting to die when off throttle. So when i get some time i get back to the adjustments and trying to sort it out...
  3. BDClone

    Idle is over 2700 rpm Help

    Ok the bike is running but still need a few adjustments I think. @warp9.9 tell me if I am wrong but as I adjust the throttle stop nut it seems like I have to adjust TPS as well. I had to rebalance throttle bodies. Running 12 min tune now. Idle should be 1000 or 900 rpm and currently at 1300 rpm...
  4. BDClone

    Idle is over 2700 rpm Help

    Yes I mucked it up. I did mess with the nut on the end of the of the throttle bodies.... throttle close stop screw? I am currently running Ramair filter and Carpenter sidewinder exhaust. Both installed last April and May, dyno ... all good. More recently I started getting a fluctuation while...
  5. BDClone

    Idle is over 2700 rpm Help

    Thank you, I will start fresh in the morning if i can ever fall asleep. I keep running through everything in my head. Be careful up there and stay safe
  6. BDClone

    Idle is over 2700 rpm Help

    I saw were Claviger was talking about disabling the ISCV in TuneECU and doing Manual tune. How do set the manually if it comes down to it?
  7. BDClone

    Idle is over 2700 rpm Help

    It would surge under idle. When checked in TuneECU they were all 3 different. I have had the bike a year (brand new bike) and never touched any of this till now. I did mess with the throttle plate bolt ( I think that's what it called) could i have gotten that out of wack? Steel I could give you...
  8. BDClone

    Idle is over 2700 rpm Help

    No, it's all clear.
  9. BDClone

    Idle is over 2700 rpm Help

    Yes everything was working properly before I did the throttle body adjustment and started tinkering. I have been trying to do the ISCV adjustment. Seems like the more I do the farther things get out of whack.
  10. BDClone

    Idle is over 2700 rpm Help

    Yeah I considered that. Maybe take off both sensors and test them with a voltage meter?
  11. BDClone

    Idle is over 2700 rpm Help

    I had adjusted my throttle bodies and figured I would also do the ISCV adjustment in TuneECU. The Primary TPS is set to .60 volts the ISCV reads .63 volts. Adjusting the nut doesn't change anything. I have been trying to figure this out. I have the manual and have been going through all the...
  12. BDClone

    Want to Buy Rocket III Roadster Stock Seat

    No problem, thanks for checking
  13. BDClone

    Want to Buy Rocket III Roadster Stock Seat

    I just need the riders seat. I dont ever have a passenger and I will removing the rear pegs for another modification soon.
  14. BDClone

    Want to Buy Rocket III Roadster Stock Seat

    Does anyone have Roadster stock seat they are willing to part with? Not really concerned with condition as I am planning on having it redone by Russel Cycle. They make Russell Day-Long seats out of your current seat. I am located in Louisiana.
  15. BDClone

    New Clutch Install

    No issues so far. This is the clutch pack that Carpenter puts in when they do engine upgrades
See more
Back
Top