What would cause injectors not to open/close? Bad ECU? Please read!


TURBO200R4 said:
how much will you sale it for?
where are you located?
Click to expand...
I'm not selling it until it runs right. Located right near Washington D.C.
 
Neville Lush said:
Get your injectors sonically cleaned properly. I bet they weren't done well.
Click to expand...
They were cleaned and flow tested professionally, as I've mentioned. I have the printout that shows the performance of each injector. This guy specializes in this and I've worked with him before. He's got flawless feedback!
 
CrzystghndKC said:
Bike has sat for 5 years so that's around 2017 and it's a 2005 with only 3000 miles in 12 years? I gotta feeling it's far from an ECU problem. Are you sure it ever ran?
Click to expand...
Yes, some guys buy bikes and barely ride them. My Thruxton hardly has any miles on it because it sits most of the time. As a matter of fact all bikes I've purchased were about 3k miles or below, no matter the year, and were mint like this one. Plenty bikes out there sitting unused.
 
The bike is all stock. There's no power commander or any added immobilizer. No other accessories either.

Thank you for the attachments! I've gone through all the steps you provided and everything checked out.
The injector OHM reading was a little low, between 11.2 to 11.4. Manual states 12.5 to 14. Not sure if this is low enough to cause an issue.

I do have TuneECU, just haven't used it in a long time. I had to update it and register it on my new phone. Unfortunately there were no error codes at all; I've checked numerous times. I'm attaching a screen shot of the injector pulse time.

So far I cannot find anything wrong no matter how much I look. All the wires look good, everything I've tested has continuity, and there are no shorts or open circuits. Fuses are all good, relays click, pump comes on etc.

Yesterday I started looking for crank and cam angle sensors. There's one on the bottom of the block by the driveshaft. It was a little gunky so I cleaned it off. Not sure if that's what made a difference but I got some sputters out of the bike yesterday and was actually able to start it up with a little help from ether. It wouldn't idle and I had to rev it to about 2k rpm to keep it going. Never got any better so I quit.

Today I decided to completely drain the tank and put fresh gas in it. I couldn't get it all out last time when I added gas to it. It won't even sputter today. I also took out the crank angle sensor on the very bottom of the bike. It had some shavings on it so I cleaned that up too. No difference.

**The screen shot is from today**

Any other thoughts?

P.S. I don't have a manual.
 

Attachments

  • Screenshot_20221229_160945_TuneECU.jpg
    49.7 KB · Views: 23
Last edited:
I got one better my first Bonneville was 3 years old and had 47 miles on it.
 
Have you checked & set your tps...
 
audisport44 said:
I have not. Do you have a good link for it?
Click to expand...
You set it using tuneecu, normally to 0.6v
Go to adjustments & tps, turn your primary tps on right side throttle bodies till it's set at 0.6v, then dont forget to reset adaptions.
Haven't done it for a while so there is many on here that will help.
 
r3badboy said:
You set it using tuneecu, normally to 0.6v
Go to adjustments & tps, turn your primary tps on right side throttle bodies till it's set at 0.6v, then dont forget to reset adaptions.
Haven't done it for a while so there is many on here that will help.
Click to expand...
Also tps could be shot. Later ones have blue internals & older black. You will have to take it out to check that.
 
You must log in or register to reply here.

Similar threads

Valve noise below 1700 RPM, what can cause this?
Replies
7
Views
362
warp9.9
2024 Rocket R No Start-Unusual Cause
Replies
1
Views
58
wildchild
bad cooling fan need to replace
Replies
9
Views
350
Mongler07
To Optimate or Not?
2
Replies
12
Views
830
Azisbest
Rocket not starting -Roadster
Replies
2
Views
186
Hooleymyster
Menu
Log in
Register