Aftermarket led turnsignals

My cousin powdercoats AND welds...i may have to pay him a visit!
 
I'm glad I'm a simpleton. Stock looks great to me. Glad you like it!
 
Last edited:
Yep I in love with this new set up , can not get enough of it
 

Attachments

  • 385D9475-5AA3-4A19-89AF-FD6019799C58.jpeg
    141.9 KB · Views: 86
  • C91041FE-A6E1-4009-89F4-A21EE605D13F.jpeg
    203.6 KB · Views: 93
  • 51DEE70E-B4BD-4A35-A6FC-7D321458E0C4.jpeg
    244.6 KB · Views: 78
  • 30CAE633-3C57-4E20-9116-88C3BAF88AD1.jpeg
    279 KB · Views: 79
  • 8F5033F0-7A5B-408C-A6F2-DC4BEDBFC86D.jpeg
    238.8 KB · Views: 70
  • 78D11EB9-9F0A-465A-BA93-E1DF39F8E845.jpeg
    338.6 KB · Views: 78
bccass said:
Replaced my Wunderkind with Analog Motorsports. Slightly smaller, slightly brighter.




Click to expand...
Did you get the Wunderkind turn signals shipped to the USA? I tried to order a set but they do not include the US in their shipping drop down window. Even e-mailed them with no response.
 
bccass said:
Replaced my Wunderkind with Analog Motorsports. Slightly smaller, slightly brighter.




Click to expand...
I think with any set of aftermarket LED turn signals rocket looks much better then stock towers I like both , what about rear??
 

Attachments

  • 5DB6DC73-55CC-40E1-89B4-5FF7360B9616.jpeg
    65.6 KB · Views: 22
boosted20v said:
What all was required in making these work, and what did you do for the rear
Click to expand...
My front and rear are the same! No resistor required direct swap plus solder your stock turn signals connectors! Rear fender needs to be disassembled from bike to make identical holes for turn signals and rerouted wiring from swing arm to under the tail and all wiring must be stripped from isolation to cut Black wire from junction and solder in almost near the plug to live side license plate light on swing arm!! Or live the license plate under taillight and you don’t need to mess with wires at all just rerouted all harness under seat!! It looks and sounds a lot off work but actually it’s cut one wire off isolate, same wire but in he opposite side open isolation and solder one new black wire and solder black new wire which you extend with black wire on plug for license plate!! One place cut two places solder and new wire protection or electrical tape. Rear turn signals same plugs but red tape market from factory Right side, without Left side, square plug is LP light
 

Attachments

  • 6B13DEB4-1E73-4D73-AEF8-DA3E1B95C9E4.jpeg
    146.4 KB · Views: 37
  • 7C76D089-59DE-49FF-B81E-69458A6BBEA1.jpeg
    176 KB · Views: 44
  • 2990DFFA-68D8-4623-8B60-E3A9DA304CFB.jpeg
    85.8 KB · Views: 43
bccass said:
Replaced my Wunderkind with Analog Motorsports. Slightly smaller, slightly brighter.




Click to expand...
The Analog doesn't seem to fit the shape of the Triumph rubber mounting piece. Does it need adjusting to match mounting piece or is it not shaped like the mounting piece end? The Wunderkind seems to fit right.
 
You must log in or register to reply here.

Similar threads

Aftermarket
Replies
5
Views
117
RugbyRef
New aftermarket rear shock!
4 5 6
Replies
54
Views
3K
Jagster
Is it a risk to put on aftermarket pipes without a tune?
2
Replies
11
Views
531
A1A Rider
LED headlight options?
Replies
4
Views
349
Hollow Man
Aftermarket Clutch brake lever
Replies
5
Views
1K
atomsplitter
Menu
Log in
Register