torque

Had a Motor Trike conversion done on my 2016 Rocket and getting a terrible front-end wobble when accelerating. Motor Trike says I need to check the torque on the steering head top bolt and lower bolt. How big a job is it to do and is there any special tool needed?

I can not find any info on torque specifications and torque pattern anywhere! Can someone point me in the right direction?

2022 GT (23K miles) I'm looking for the torque specification for the banjo bolt on the gas tank end of the main fuel line that goes to the fuel rail. I'm unable to find anywhere. Is there a PDF of torque values? I've looked in the tech manual PDF with no luck. Thanks in advance, Larry

Hey y’all, Today I finally replaced my sump pan on my 2015 rocket 3 roadster and when putting the new pan on, the screws broke before reaching the indicated spec of 12Nm. Is it recommended to replace these bolts each time? Got lucky since torque is so low and was able to remove the broken end...

Can someone please post the torque spec for the front axel. I haven't been able to find it anywhere. It seemed to be put on by a gorilla when I removed it. Thanks in advance.

Found a 2016 roadster for 7500$. 9k miles. Any major things I should look for?

I'm sure I'm not the first to ask this.. but if(?) the Storm is only different in its software, then is this possible? I already have a custom tune from @Penner i did couple of years ago., so not sure if it will be possible to add power

New 2024 Storm R3s with photos https://www.motorcycle.com/bikes/new-model-preview/2024-triumph-rocket-3-storm-r-and-gt-first-look-44599522

Hello there! What are the torque specs for the final drive fluid fill and drain plugs on the 2.5 liter? I saw one thread the drain was 25nm. Is this correct? Thank you! Also, my wife and I are headed to the UK next month and will be attending the Triumph Factory Tour. I cannot wait!

I'm a bit of a numpty, and misplaced my spec sheet... does anyone recall what the final torque spec is for the Carpenter head bolts?

Hi Can someone give me the torque setting for front wheel spindle,pinch bolts and caliper bolts my 3r. Just changed the tyre. Thanks Martyn

G’day All ! Firstly, thanks for all the help / advice / parts (Ishrub!) so far... Briefly, and pls delete if this info already here somewhere. Point me towards it tho first pls... What’s the best Torque/HP upgrade route? 2008 Classic, custom pipes, ram air, ozclaw, Mittzy rad tube, air box...

Hey guys, I need to remove the plastic piece around the right fork to use the SealMate fork cleaning tool in the hope to fix the effin leakage. Anything I should know before taking off all these screws, or anything I should pay attention to before starting to unscrew them? What is the torque...

Hi all my front rh caliper seems to be dragging , have checked the pistons and One has rust spots on it so have ordered a piston and seal kit off eBay , I was going to split the calliper to rebuild it but can’t find the torque settings for the 4 bolts that hold the calliper together , any clues...

Hello all. Great news, ive knocked out basically all the wiring/ tedious steps to swapping my rockets engine out. Was going to buy another torque wrench specifically for tightening everything up with no issues or hastles in NM or metric. Buuut now im pondering has the flip side to my wrench been...

I’m going to put on new dresser bars so I want to make sure it’s torqued correctly. In my book the only value I can find for this bolt is “See Note”. The problem is I don’t see the note... anywhere in the book. Does anyone know what the proper torque is?

"THERE IS NO REPLACEMENT FOR DISPLACEMENT" 2.5L (2472cc) Stroker Package Want a bigger engine and way more torque than the new Rocket 3? Add 10% BHP and 12.5% Ft Lbs to your engine, throughout the entire RPM range. No trade-offs! Premium performance parts, all manufactured in the USA and...

Wondered what others observed on this subject. My honda vtx 1800, when you accelerate, it would throw you back as it propelled you forward. On this rocket, no throwing back, just forward. Have you noticed this, and if so what is the explaination? Is it 2 cylinder vs 3? Thanks in advance!

I just finished a Neville Lush piston and cam rebuild in ""record time"" with no prior experience. I had allowed myself a full five days during the Christmas holidays for the install. Well, now, more than three months later, I’m finally in a position to say, "job completed!" and share this story...

Installed the Ramiar some time ago and had the Jardine set up from new. Downloaded and installed a Tune From @HansO and was wondering how it was doing. Always ran great. Last weekend was in a long Ride and it starting acting up. Would stall under decel when coming to a stop and act as if hydro...