header

I can not find any info on torque specifications and torque pattern anywhere! Can someone point me in the right direction?

Planning on sending my headers off my 2022 Rocket 3R to Jet Hot High Performance Coatings for heat and cosmetic reasons. I was wondering, is there anything I need to be aware of doing this? Being the first time I ever attempted this on my bike, just a little nervous. Any suggestions and help...

Dyno runs charts are 2 years apart. Both Dyno are from Different Businesses. Not the same Dyno machine. Dyno1 was ran during Summer July, Dyno2 was run today in Nov. Dyno run 1 is with Werkes Exhaust + Penner Tune + Stock Headers Dyno run 2 is with Open Exhaust + Penner Tune + 2.5inch...

I think a few of us on here struggle with header pipes and heat issues, so I wanted to share my experience. I bought my header pipe used and it was already coated when I got it I believe it was gray at the time. I used it for awhile, then took it off and had it professionally ceramic coated...

can't stop looking at that work!

Hi - I wanted to get opinions about some ugly discoloration I'm seeing on the headers of my 3R. I've other threads on this forum about blue stains but nothing about these rust-looking examples. Any idea what's causing it? Can it be polished off? I'm going to drop by the dealer, so have not...

Hello all, I just picked up a 2015 R3 touring that the previous owner had a 240 Carpenter kit installed. It's a great bike. Only had 2500 miles on it. Has the 3:1 header on it with a megaphone. I messaged Carpenter and they do not have anything quieter for me. Has anyone had luck installing...

Does anyone make a heat shield for the header pipes?

Looks like Carpenter is close to producing a different header for our beloved Rockets. They say it is a "3 into 2 into 2 into 1 header" and named it the "TXL". Doesn't look too bad if ceramic coated and equipped with heat shields. Not too promising for the GT model though.

Hi, Has anyone got a way of stopping the exhaust header pipes on the RHS burning a hole in my wet weather gear just below the knee, it has happened twice now? Cheers HB

I noticed a hairline crack on the middle (#2) header almost two weeks ago. The crack is approximately parallel to the engine face along the exhaust ports. Its jagged appearance indicates that it might well have started as a shorter (hydroforming-related) stress fracture from where it then...

Good Morning Everyone, I recently installed Paul's Viking Header exhaust, and when I installed it, I saw that the factory gaskets were still inside the ports, so I went ahead an put on the new header. When I did this, I made sure to make sure it hadn't rolled downward, and I thought I had it...

After a 140 mile ride today, checked the temperature at each exhaust clamp: Front Cylinder - 160 F Middle - 193 F Rear - 184 F Does this seem normal? Has anyone else checked their header temps after a ride?

This site has been a bad influence.... Although I really do like the looks of the stock header, the quest for “more, more , more” eventually took me down the custom header path. I finally settled on the 2 ¼ diameter header and exhaust system from CES Racing Systems. I like the design, now even...

US$16 Ignore the tip it is scuffed. Not sure what use the other bits are. 06 2006 TRIUMPH 2300cc ROCKET III EXHAUST HARDWARE #X15 | eBay

Selling a few parts here. All prices are plus postage, Removed from a 2006 Rocket III with 20k miles on it. Triple TORS silencers including exhaust brackets and heatshield covers. These are in decent condition, there is a scrape and some cracking of the chrome on the underside of the bottom...

Several days ago I got the chance to install a @Paul Bryant header. It's done in chrome. Yesterday I installed a tune reccommended by Clavinger, Headers and ramair 226. Did the 12 minute tune and reset adaptives, so she was ready to rock and roll. The other parts of my set up is RamAir and...

Header wrap sure did cut a lot of the heat on a Paul Bryant crossover Pipe. It know feels lot cooler than the stock pipe was!

Well after scouring the Google's looking for a cerakote applicator to refinish my recently acquired CES, I finally found my man , or so I thought ? After mailing photos of a new CES header , most applicators said fairly and honestly enough that they couldn't match the finish . One however ...

Im trying to get hold of an exhaust header midpipe muffler for my 09 classic. Prefer to buy here in Australia only due to shipping. New or used is good. Thanks in advance.