I’ve got an oil leak, think it’s coming out under the clutch lifter arm. Red arrow in the pic below is my first guess...reasonable?
That part appears to be a seal but isn’t ID’d in the manual or online parts diagram. What is that? An o-ring, washer, packing? Anybody know what size?
Can I pick it...
Hi had my clutch fail, upon inspection the roller bearing that holds the plunger in place had collapsed I'm Tryng to locate parts but triumph world and the triumph manual list it as a needle bearing I have attached a pic its not so clear to tell as it lists a wavy washer and some other washer I...
Hi guys I need your help with something.
It's been a few years since I had the clutch cable (converted to TTS hydraulic). I'm going back to the cable with the 2.5L stroker, but I seem to be missing a small part.
I reckon a plunger and spring are missing from my clutch switch.
Could someone...
I'm starting in on a Lush cam and piston install on my '11 Roadster and would appreciate advice from anyone with experience installing a Barnett clutch. I've come across posts where some say to leave out the stock anti-judder seat washer and spring, which is not part of the Barnett kit...
Hi all,
Bought my 2013 Rocket III Roadster in Jan this year as an insurance write off, cosmetic damage only. It had 962 miles on the clock and I have no idea of the history, how long it had stood and where.
Got it all sorted and back on the road but have had clutch "issues" ever since.
The...
Ok, this is driving me crazy, my clutch we out of adjustment suddenly, checked the cable and it is good, (only a month old) I have adjusted up, down, and all around, and I can't get it quite right, I have never had this much trouble with a clutch before. currently,
When stopped you can feel it...
So I'm pootling along in 5th and coming up to a roundabout, go to change gear and find my clutch lever is limp.
So i had to take that roundabout in 5th gear :eek:
Worked the throttle then to get the tranny to that nice unburdened point in between being pushed by the motor and being dragged by...
My switch broke recently. I have it bypassed right now to run the bike but I don't like my fuel gauge being inoperable. I know it comes as part of the entire switch assembly do in willing to buy that. However I really don't want to spend $160 just for the switch. Anybody got one they are willing...
I've been fighting with the hydraulic clutch on this since the build... with leaks due to bad O-Rings and such, but one issue that hasn't went away is under Hard acceleration the clutch lever becomes limp. You can actually feel the lever begin to collapse under full throttle , you can then give...
So today my clutch switch broke in the housing. To start my bike I have to hold the little pin in the switch to complete the circuit then start the bike. Is there a quick fix that I can do to avoid having to do manually hold the pin in? I'm planning on riding to the dragon's back tomorrow so...
I got my new clutch kit with springs from Carpenter Racing. I will be replacing the oil and coolant and ordering a new clutch cover gasket. It was mentioned that I should change out the detent spring as well. Only 4700 miles on the bike. Any thing else I should look at possibly changing while I...
I broke my clutch cable yesterday on my r3t with 40 k on it. I can live with that problem but what occurred with it has got me completely baffled. The linkage on the shift lever bent in a 90 degree angle and snapped the shift levers pivot point completely off. Any ideas as to why a broken cable...
When installing this kit a few years ago on my bike, it occurred to me that the TTS instructions that come with the kit are a bit out-dated, and completely missing the stage 2 bits (intercooler and smaller radiator), hydraulic clutch and supercharger oil circuit installation instructions.
Also...
I'm starting to have issues with the clutch switch. Is there an established cleaning procedure to perform?
If I replace it, since it's a $106 part (you could replace just the $6 switch component itself on my Suzuki </gripe>), is the switch portion of it compatible with any of the later models...
The fibers and cover and springs installed. My question is, before I put the front cover on. I have tried pulling on the lifter. It moves in and out. But if i pull on real hard. Is it supposed to move out and compress the springs. This is all new to me. I was wondering how it works. Or when...
05 Roadster gray motor
I replaced the dent spring. I received a mtc clutch kit. When I put the clutch outer drum in. The drum seems back far enough. But the two gears are not completely meshed. The outer one seems to be overhanging the primary gear. The book says to go thru a hole and preload...
I have a Decosse's keyless ignition fitted and have been having water ingress problems keeping the ignition live after rain or washing. I have tried dilectric grease and covering the holes but all to no avail. This weekend I have procured and fitted a momentary push button and fitted it to...