clutch

Recent contents Top users
  1. wjb

    Another clutch question

    My clutch has been giving me fits lately. It all started when both the clutch lifter shaft and lifter piece broke. Those parts have been replaced but then the clutch would not completely dis-engage and would drag some even with the clutch lever pulled in all the way, and there was also no way...

  2. Hi...I'm new here. Noisy clutch question.

    My 2018 Triumph Rocket 3 Roadster, when shifting from 2nd gear to first gear, makes a weird whirring sound followed by a clacking/clunking sound and some slight jerkiness as it slows to a stop. I took it to the dealer shop for it's 10k maintenance and I asked them to test ride it so they can see...
  3. buddazero

    Clutch Freeplay, Riding the Clutch, Maintaining & Adjusting the Clutch

    Hello everyone 🖐 Below is my personal experience about motorcycle riding for the past 5 years, and my learning journey with the rocket. My questions are highlighted in bold, and if anyone can answer them, please do so, as I am still learning. I've been riding my Rocket 3 Roadster 2018 for 4...
  4. Jack

    Clutch shuddering

    I'm riding a 2004 R3. Done only 34,000 Kms I've noticed the clutch has developed a shudder when I take off. Has anyone experienced this and what advice can you offer
  5. Korte

    clutch reinstall thrust washer locations on 2013 r3 phantom red roaster,,i had this bikes clutch in a box ,basket case when i bought it,,,HELP

    were does idem part number 23 go and its place on the reassembly per the factory triumph manual I HAVE,,its called a spacer clutch assembly part number T1172727,,i got everything thing else and identified there placements per the manual on the tranmission output shalf,,but this spacer needs to...

  6. Hi I'm new on here and have a little problem with my clutch.

    I have a 2006 rocket 3 and the clutch pull arm broke and put a mark/groove in the pressure plate so after reading a few comments on here I ordered from fowlers the pull arm, thrust bearing, washers,pressure plate, and a new arm to go to the cable. I ordered the newer pull arm and got sent the...
  7. evo

    Ways to disable need for Clutch to start bike?

    I hate having to pull the clutch in when starting the bike...anyone have any knowledge on how to disable this? Is it possible, or is this something you can do with TuneECU maybe? This is for the new 2.5l Rocket 3 btw... ta...
  8. captainsparkle.com

    Fibre clutch plates

    Hi all, been a while since! I have recently "burnt out" my clutch (2007 Classic). the friction plates are well below thickness, so I ordered a new set of EBC, eventually! At the moment they're like rocking horse excrement, so I was pleased to find some, & a set of EBC stronger springs. I would...
  9. Kens

    Clutch Oil spray nozzel

    Has anyone ever had the nozzle out, if so, is it just one piece and which direction does it go back in, as it's got a cross drill hole in.
  10. Ishrub

    Are Suzuki Hyabusa clutch springs special?

    I think I remember posts a few years ago referencing Suzuki Hyabusa clutch springs being very strong upgrades for Rockets and of a par or better than Barnetts HD ones. The stock Triumph ones were not very impressive apparently and the common aftermarket clutch kit providers were not much if...
  11. Motortard

    StallingWithCltuch

    Good Day Everyone, after around 300 miles I've noticed that my 2021 Rocket 3 is hard to launch from a stop. Almost as if the clutch engages too soon and engine stalls... When 1st test driving it 1st time I didn’t have this problem and while its warming up it drives well… Once its been running...
  12. Jonathan Nikolaisen

    Clutch adlustment

    I need help on the engagement at the bottom of the clutch cable. I had fixed it an now I have nothing again. I am adjusted almost all the way to the bottom of the screw set so now what... Do I move the cable end lower or higher in order for it to engage oroperly?
  13. GHOSTROCKET

    Clutch not engaging

    I changed bars out and now my bike will not engage in gears... I need to know how to adjust clutch to allow bike to engage.
  14. GHOSTROCKET

    Clutch issues

    Anyone switch bars and have issues with clutch not engaging? How did you fix it short of changing out the whole cable assembley?
  15. Stefan67

    Clutch slip

    Guys I need to pick your brains, ive got a r3r, 2588 ks on the clock..my issue is im getting the clutch slipping badly...but....only when the bike warms up, cold it's no issue but at the moment I'm on the side of the rd waiting for it and me to cool down. I've installed penners unrestricted...
  16. REBLX136

    Clutch Bark

    I’ve noticed a slight bark in the clutch on take off just as it picks up the bite in first, it’s not constant and doesn’t matter if she’s hot or cold, I can feel the bark through the lever and it repeatable but not consistently, shifting isn’t effected. Anyone else experience similar, she has...

  17. Engine dies when clutch pulled in and chnage down

    Hello all I have a 2021 Rocket due for its first service, however I have noticed more than a few times the engine dies when changing down coming up to traffic lights etc, starts no worries, but is a bit of a worry. The bike idles quite well normally. Thanks
  18. Micksan

    NEED CLUTCH & BRAKE LEVERS & MOUNTS

    I have a 2014 R3T. I just converted it to a trike. The wife rides also. Problem is that the lever setup for the T is set to far out for her hands. She has to take her hand off the handle bars to get at the levers. I have tried every source. No adjustable levers for the "T"s. Lots for the...
  19. Micksan

    HELP>>> Need to find adjustable ,or fixed Brake & Clutch Levers

    The stock levers are to far out from the handlebar. My wife says she can not ride until we can get them in closer. I am 6ft 3 with big hands and find it is a reach for me also. Found out the hard way that the Roadster and touring models have much different levers. Can find for Roadster but...
  20. Thedoctorr

    Clutch Switch Removal

    Hi All This is my 1st rocket in my 23 bikes owned over many many years. I have searched tirelessly through the service manual on how to take out the clutch switch but nothing on how this is done. Can anyone tell me how to do this please. regards Neil
Back
Top