throttle

Quick question: Do the secondary throttle plates adjust when applying throttle?

Hi all I have done a search but couldn't find anything. Just wondering if anyone has tried the Mag Throttle cruise control/throttle lock. I am looking at it for my 2016 R3T All the info is at Mag Throttle Store Seems like a good idea but I just have some concerns as to whether I will be able to...

Before I start, I must say I don't think I'm an idiot..... So I'm trying to adjust the throttle cables as per the shop manual. It's not my first time but every single time I go thru the same thing. I adjust the pull cable with free-play of 2-3 mm at the handle. Then tighten the return to 2-3mm...

Has anyone used the electric throttle lock by magthrottlestore.com?

Has anyone used these? Handlebar risers (Triumph cruisers, with 1" handlebars) | TwistedThrottle.com Dont neex the extra pull back of the rivcos.

How often do you find the bodies needs checking / balancing?

First ride since balancing the throttle bodies. Wow, what a nice improvement! Smoothed out the idle and pulls better, thru all gears. I have noticed a less vibrations at all speeds. Ten minute job with tune ecu. 4 hours total fussing with the stock air intake system! I was only 30 point off...

My recently purchased 2005 Rocket has developed a problem that sounds like a throttle position issue. I purchased the bike with 10,000 miles on it back in February and have since put on another 4,000. A couple of weeks ago I noticed while cruising along at about 2500 rpm it started to feel...

I found some info on the subject of adjusting throttle bodies on a R3T here but not what I wanted to know. Has anyone here adjusted the the throttle bodies on their Touring? The service manual says it can't be done with the Triumph Diagnostic Tool so I'm assuming it can't be done with...

My R3 has been requiring more cranking than usual and I have to give it some throttle to get it to fire up after setting overnight. I need to nurse the throttle until it warms up, then it will hold a low speed idle. I've reloaded the map using TuneECU, and had no error codes. The battery is...

PCV install, with stock filter system, 2016 Roadster To get at these little buggers,:unsure: I assume you have to start with the throttle body intake plenum, remove from the throttle bodies and intake duct and work backwards from these to expose the connectors, or is there an easier way. Are...

SOLD!!

Ok boys...I have a rocket in my shop that's throwing the code above. It recently had the TPS changed (5,000 miles ago or so) and TuneECU shows it functioning normally as best I can tell. Thougts?

Okay this should be easily answered. I have many times balanced the throttle bodies on R3's, without the stock air box its pretty easy while using Tune ECU. No problems with this. From reading other threads I know that the vacuum hoses crack with age and may need replacing. I'm also OK with...

Used TuneECU for the first time today. Checked my throttle bod sync as I suspected it maybe out (one cylinder sounded a bit lazy/out of sync). They were a long way out so went about syncing them. The adjusting screws were very hard to get at even with a very long screwdriver. In addition the...

Hi Guys Been riding big bikes ( 600cc+ ) for twenty + years and had the average selection of No torque peaky power nervous front end jap stuff Been a long time fan of the Rocket lll since they first came out but family ,work, life and finances would not let it happen . But this year finally got...

Just a quick question. I am going to download this fuel map:- Rocket III Roadster Jardine Full Exhaust 3xK&N RU-2780 air filters under exhaust Fuel up to E25 Minimum 98 RON (91 US PON) fuel Do I need the secondary butterflies in or out with this tune?? Thanks for your help Dunmer

Are the stock throttle tubess any stronger than the heated grip tubes? The reason I ask is that I I am interested in putting some heat demons in my bars but have no interest in my throttle tube breaking.

After about an hour of very pleasant riding I noticed that whenever I released the throttle to start to decelerate there would be a jerk rearwards, and when applying throttle from zero there would be a jerk forwards. This was in all gears, but not when shifting it seemed. Then I stalled at...

Hi, Do the throttle bodies need synchronising or checking from time to time for Val cave and if so can they be checked and balanced with TuneEcu or checked with manometer? Can the TPS be checked and set also with TuneEcu? One of my intakes sounds a little late/flat. Get the odd pop on rapid...