I have a mostly stock 2006 R3. The only significant change is the CAT box removed with tune flashed at dealer. The bike has been very under-used since 2013, mostly just for 2-Up with my wife. The last time riding was last fall and it began to show the dreaded high idle symptoms. The bike starts...
what could cause the rear position light to stay off when the ignition is turned on I checked the fuse, I checked the rear led bulb ( brake light works|) it used to work without problem before
.could it be a glitch when I changed the headlights and reconnected new headlights ?? both old...
Have been an R3 owner for over a year but have had most of my questions answered without having to ask any of my own. But now I'm absolutely stumped with this dang clicking on start u .
There is absolutely no rhyme or reason when I will get the click. Sometimes when it's cold. Sometimes when...
Just got an 05 Rocket and it starts and runs great. The problem is the lights will go off suddenly. Headlights and tail light both out. If I get under the tank and wiggle around the wires near the ignition switch which was relocated to the left panel, I can get them back on. Can the switch shut...
My 05 that is stock, and only 3,200 miles, has developed, to me, a strange problem. Center cylinder isn't running right. After a few minutes run time, front and rear exhaust manifold temps are 285/290 center is 230. I have checked for loose coil wires. Bike has external fuel pump, set to 40...
Hello everybody my name is Pippo, I type from Italy and this is my first post. I can't start engine when my rocket III is hot. I can start it only when cold. Who can help me? Thanks in advance
Every time I turn my bike to the right the power would shut off completely leaving me dead until I turned to the left again. So I had no dealers opened (Sunday) and towed my bike home waited patiently and called the dealer on Tuesday who told me I needed a new ignition and the part cost approx...
I am going to explain this in great detail and hopefully somebody will have a solution. turning the key to the on position the headlights will flash and then go out completely. This is prior to hitting the start button. Bike will start fine but have no headlights. Today i replaced the rely...
I've had a problem with low rpm roll on since last summer, got worse in rain or damp. I just had my bike in the shop, he looked everywhere for any loose connections or mouse chewed wires, found nothing except maybe one plug wire nor on tight, and he said one of the ecu plugs seemed not clicked...
Has anyone fitted a Healtech QuickShifter as I can’t work out what I need to do with the two shorter green connectors I will ring the supplier later but if anyone can help in the meantime,Tia
It about drove me nuts today. Every stop . . . fiddling with the clutch switch and actuating the key in the ignition many cycles to get it started. I can't figure out if it is the clutch switch or the ignition.
I am about ready to take it to a "stealership" hauling it in and leaving it until...
Hi all, well, I must be feeling better, as I went out today, and pulled the front cover off my 05 Rocket. Besides a juddering clutch, which I think is from me leaving out the judder spring on my Barnett install, I've had this weird shift thing going on, for quite a long while. Kinda hard to...
Hi all, Had a clunking noise started at the bottom of the engine on my 04 rocket. When dropping into 1st - in traffic or at a junction - and pulling clutch in, the engine clunks and the bike tries to judder slowly forward. Realised it was probably time to fit the new Barnett clutch plates and...
Idle speed control motor was out of adjustment. Started to tighten the nut to get the 5mm and the plastic collar broke right off. Is this collar necessary for stepper motor to work properly?
I was experiencing what appears to be a fairly common vibration from the engine at around 2400 rpm that smoothed out greatly when the clutch lever was pulled slightly. It wasn't enough to make the bike un-rideable but was annoying on long trips as the vibration from the handlebars left the hands...
Honda Moly 60 is no longer available in UK so I wondered if any of you know if this would be any good as a replacement final drive lube?
AS60 Molyslip 16001 500g Tub Anti-Scuffing Paste - Molyslip Anti-seize & Assembly Compounds - Lubricants & Greases - Product List - Drake Tooling & Abrasives Ltd
Hi all,
My 2014 roadster has a foreign object in the oil tank (don't ask what or how- I want to stay married).
Have been trying to download a manual to check how to remove fuel & oil tanks but so far only ones I've found want to install other software or ask for payment without me being able to...