pcv

Hoping someone can help. I have a 2014 roadster with CES Racing exhaust and K&N filters. Im looking for a tune for PCV. Please help.

I was reading here that PVC wasn't available for our bikes . Not sure if anybody has seen this yet but they are now good to go 👍

Howdy fellas. Looking for a map to burn the storage gas out and get me to the tuner after I install the DP double customs (full length), crossover pipe and Ramair. Mr. Dougal is a 2017 R3R. From what I'm reading on here, a Ramair/TORS map should get it close. Once I get it custom tuned, I'll...

Hi Gang, I understand this request is opposite from the usual map request but has anyone developed a map for fuel economy? I understand I can go all 0's on my map cells but I am looking to see if anyone has done one better. PCV w/AutoTune on a 2011 R3T. Stock air intake with Jardine's 3/1/2...

Afternoon chaps Strange problem I’m having, purchased a small bundle of Carpenter parts last weekend and just fitted the Brute exhaust today,with the parts came an untested PCV . Running the bike on a tune from tune ecu as previously no codes,when the power commander is hooked up...

It looks like the kit for an 05 comes with an 18mm O2 sensor. I think the Rocket has a 12mm sensor stock. For those of you using auto tune did you have to install a new bung in the exhaust to make this work? I was really just hoping to use the stock hole. Thanks.

Good Morning Everybody, I've been searching the interwebs for quite a while now, and just about everyone I have called and or visited uses the PCV system to tune in their shops. Almost nobody has heard of TuneECU. Does anyone know of a tuner in Florida that can actually use TuneECU? If not...

How many of you have done pressure based tuning? I am having issues with the pcv ignition module. Is there any other software or ways of tuning via pressure base besides Dynojet? I am not impressed with the them. The auto-tune is slow, I can do better with data logging and manually putting in...

We keep losing oil cap/dip stick off. I'm thinking it's under hard acceleration. Is anyone else having this issue? Is there a way to remedy it ? Venting crankcase to exhaust or better venting in general.

I'm going to install a PCV and have it dyno-tuned at the same time. My question is should I load up the stock TuneECU map or can I keep the map I've been using with my bike? TORS, cat delete, and ramair.

How are you guys installing a 3 bar map sensor for Pcv and Tunecu for boost applications? I read this post from a while back. It explains how to setup a 1 bar map for pressure base tuning. but not much about 3 bar. How To: Add Pressure Input for PC-V

Hi all, can someone let me know which model of the PC autotune I need for a touring? When I look it up there seems to be a single sensor and a dual sensor? Am I going to need to weld an o2 bung or does it just screw into and replace an existing OEM sensor? I’ve tuned with Tuneecu and am...

So I ordered a set of the Shorty Outlay exhausts and the Ramair. I know that the 12 minute reset wont do for this extent of mod. Is there a particular tune that works best for this combo on a 2018 Rocket 3? Do I have to go PCV and AT route? What is my best bet. I love this bike and don't...

I recently saw a thread, where the man in the tin shed was taking data from a PC3, after a cam install, then sending data back to guy with the new cam to make adjustments to either the PC3 a/f map or directly to the bikes ecu, I'm not sure which. Anyways, I'm installing Paul's header, a new...

Hi folks. Where should I begin. Ok. My bike is 2006 Classic, cat removed Tors fitted, RamAir filter, Hanso ECU tune and two weeks back fitted PCV and dynoed at my local shop. Dyno went not bad was able to pull out : 142.5 ponies and 151.7 Torque. Bike ran perfect for about a week and then it...

Say a tuner does it with PCV, can the resulting table be applied with TuneECU? ... or would it be of no use?

Loaded a Tune Ecu tune I got from Hanso for my 2008 with Ramair , Viking Header and now single Viking silencer.At the time it was for header and Staintunes. I have PCV with autotune which I loaded with a zeroed tune in the PCV and Hanso's AF table in the autotune. Everything seems good except...

Hello! I am just getting back into motorcycling as my children are now old enough to stay home alone during the summer. It has been a while since I tinkered, and have forgotten quite a bit. I have just re-loaded Power-Tripp's free tune for R3Ts and currently have a zero map in my PCV-AT...

Can anyone who has a PCV help me out ,If you open PCV and then power commander tools ,calibrate, gear position,and write down the numbers in the table. I have messed mine up Thanks All

I've just ordered a PCV and AT, so I'll need to "accept" and change the fuel map etc, can the Android do this task? PCV is only windows based, but I believe I have seen in Tune ECU on my Adroid something about accepting trims or such. Does anybody know if the droid will do this or do I...