Has anyone used the 3into 2 from D&D ? They sound good and add some power. Would like your input good or bad as I'm considering it for the spring
D&D exhaust.com
Made a home made version of this
Shorty Exhaust for the New Triumph Rocket III
Got 2 exhaust pipe expansions that slip over
cat bypass pipe ( 1 5/8" expansion ID)
Then cut just short enough that , I could bolt in
the 2 baffles , but leave 90% of baffle hanging out
Capped off ( blanked ) 3 rd...
so I was bored this past week. I removed my rear tire to get it changed. While I was doing that I removed the three exhaust pipes. Then I wanted to hear how it would sound. It sounded pretty good. so are there side effects from running without those exhaust pipes? I'd like to get three custome...
Hi has anyone with Jardines exhaust ever taken the baffals out and does it sound more deeper and louder? And if so do you have a audio of it?
Or has anyone ever just taken the fiberglass rap off?
Or cut the baffal in half?
Could anyone tell me what would sound the best?
I like the sound of the...
Anybody out there with a little knowledge or input regarding the Jardin Exhaust System? Installed full system with KN air filter. Was told the only way to get rid of popping was to put the power command on. Did that, dealer couldn't map it so had it dyno'd. Still have popping, took -99 values at...
What brand of exhausts are these?
I like the way they get closer to the bike's body compared to the stock ones.
I also like this kind of gas shoks, maybe a little smoother than stock, nor do I know the brand...
It's all go info , but exhaust section starts @
52 of 112 on pdf file = bottom #'s
http://www.nightrider.com/biketech/download/engine_dyno_guide.pdf
Wayne
Great minds think alike... or at least their computer programs do. :D
The specs for my custom exhaust system have been run through 2 different computer programs (at 2 different builders) and they are within 2/10" of each other... equal length, of course. They also both agreed on using 3 step...
Greetings Everyone, Yes, I'm afraid so, another exhaust question.
I am looking at the D&D exhaust 3 into 2 option. It seems to make the most sense for what I want to do. I have heard so many things about the Jardines and how they have fit & finish issues, that I am being spooked into going with...
so digg'n this... the gregstr has set the bar for cooooool in exhaust.
texas no less.. who would have thunk it
my hats off to you greg..
i wonder if they could do a pic of me on the pipes.. you guys wouldnt mind would you :eek:
click to enlarge... bet brians wife wishes it were that easy..:D...
1. Stock cat and pipes
2 Bypass with TORS
3. BYpass with mad dogs
4. Bypass with D&D
5. bypass with other
6. TORS only:confused:
7. Other header system one of a kind
8. ??????????
Here are photos of an ARC exhaust built for a Bonneville Salt Flats bike:
Doug plans 3 equal length tubes for my R3, dropping in a twisted fashion below #2 exhaust port, then running straight back to the collector and large single megaphone. He also fabricated the mono-shock frame above...
Anyone have those, I just have those,
I bild the bike more faitter style ,and also new carbonfiber rims seen better
just have to change to handelbars, modifade seat and rear fender
an front springs and rear shoks. + litle bit more carbon,
and new paint maby.
finland we have wintter nothin...
looking to do some mod to my rocket. Seems there are a lot of motorheads on here so I'm asking for some info. I don't know what tune is in my bike, I know it runs very good. Can i elimate the cat or" clean out" without tuneboy?? Will it increase torque/power?? will it cause popping?? will the...